Skip to main content

What is Refrigeration cycle and and how work this cycle 


"The Mechanical refrigeration is accomplished by continuously circulating, evaporating, and condensing a fixed supply of refrigerant in a closed system. Evaporation occurs at a low temperature and low pressure while condensation occurs at a high temperature and high pressure. Thus, it is possible to transfer heat from an area of low temperature (i.e., refrigerator cabinet) to an area of high temperature.'
We know that the Referring to the illustration below, beginning the cycle at the evaporator inlet (1), the low-pressure liquid expands, absorbs heat, and evaporates, changing to a low-pressure gas at the evaporator outlet (2).
(The compressor (4) pumps this gas from the evaporator through the accumulator (3), increases its pressure, and discharges the high-pressure gas to the condenser (5). The accumulator is designed to protect the compressor by preventing slugs of liquid refrigerant from passing directly into the compressor. An accumulator should be included on all systems subjected to varying load conditions or frequent compressor cycling. In the condenser, heat is removed from the gas, which then condenses and becomes a high-pressure liquid. In some systems, this high-pressure liquid drains from the condenser into a liquid storage or receiver tank (6). On other systems, both the receiver and the liquid line valve (7) are omitted.)
"A heat ex changer (8) between the liquid line and the suction line is also an optional item, which may or may not be included in a given system design."
Between the condenser and the evaporator an expansion device (10) is located. Immediately preceding this device is a liquid line strainer/drier (9), which prevents plugging of the valve or tube by retaining scale, dirt, and moisture. The flow of refrigerant into the evaporator is controlled by the pressure differential across the expansion device or, in the case of a thermal expansion valve, by the degree of super heat of the suction gas. Thus, the thermal expansion valve shown requires a sensor bulb located at the evaporator outlet. In any case, the flow of refrigerant into the evaporator normally increases as the evaporator load increases.
As the high-pressure liquid refrigerant enters the evaporator, it is subjected to a much lower pressure due to the suction of the compressor and the pressure drop across the expansion device. Thus, the refrigerant tends to expand and evaporate. In order to evaporate, the liquid must absorb heat from the air passing over the evaporator.
Eventually, the desired air temperature is reached and the thermostat or cold control (11) will break the electrical circuit to the compressor motor and stop the compressor.
As the temperature of the air through the evaporator rises, the thermostat or cold control remakes the electrical circuit. The compressor starts, and the cycle continues.
In addition to the accumulator, a compressor crankcase heater (12) is included on many systems. This heater prevents accumulation of refrigerant in the compressor crankcase during the non-operating periods and prevents liquid slugging or oil pump out on startup........
(Additional protection to the compressor and system is afforded by a high- and low-pressure cutout (13). This control is set to stop the compressor in the event that the system pressures rise above or fall below the design operating range.)
(Other controls not indicated on the basic cycle which may be part of a system include: evaporator pressure regulators, hot gas bypass regulators, electric solenoid valves, suction pressure regulators, condenser pressure regulators, low-side or high-side float refrigerant controllers, oil separators, etc.
It is extremely important to analyze completely every system and understand the intended function of each component before attempting to determine the cause of a malfunction or failure.)

Comments

Post a Comment

Popular posts from this blog

how to work refrigeration cycle work

How Does an Air Conditioner Work? There are  two laws of physics  that we should review before explaining the inner workings of your air conditioning system. Combined Gas Law The first is the relationship between pressure and temperature, known as  the combined gas law  since it combines  Boyle’s Law ,  Charles’s Law , and  Gay-Lussac’s Law : Boyle’s Law  states that the pressure-volume product is constant. Charles’s Law  shows that the volume is proportional to the absolute temperature. Gay-Lussac’s Law  says that the pressure is proportional to the absolute temperature. In simple English, the combined gas law says that whenever you heat up a gas, pressure also increases. And vice versa, whenever you pressurize a gas, heat also increases. If pressure increases, so does its temperature. This is why a tire heats up as you pump it with air. If pressure decreases, so does its temperature. This is why an aeros...
2 comments
Read more

Equation of State of an Ideal Gas

PSYCHROMETRICS Psychrometrics is the study of the thermodynamic properties of moist air. It is used extensively to illustrate and analyze the characteristics of various air conditioning processes and cycles. Moist Air The surface of the earth is surrounded by a layer of air called the atmosphere, or atmospheric air. From the point of view of psychrometrics, the lower atmosphere, or homosphere, is a mixture of dry air (including various contaminants) and water vapor, often known as moist air. The composition of dry air is comparatively stable. It varies slightly according to geographic location and from time to time. The approximate composition of dry air by volume percent is the following: The amount of water vapor present in moist air at a temperature range of 0 to 100°F (17.8 to 37.8°C) varies from 0.05 to 3 percent by mass. It has a significant influence on the characteristics of moist air. Water vapor is lighter than air. A cloud in the sky is composed of microscopic ...
Post a Comment
Read more

DALTON’S LAW AND THE GIBBS-DALTON LAW

DALTON’S LAW AND THE GIBBS-DALTON LAW  Dalton’s law shows that for a mixture of gases occupying a given volume at a certain temperature, the total pressure of the mixture is equal to the sum of the partial pressures of the constituents of the mixture, i.e., The partial pressure exerted by each constituent in the mixture is independent of the existence of other gases in the mixture. Figure 2.1 shows the variation of mass and pressure of dry air and water vapor, at an atmospheric pressure of 14.697 psia (101,325 Pa) and a temperature of 75°F (23.9°C). The principle of conservation of mass for nonnuclea r processes gives the following relationship: Applying Dalton’s law for moist air, we have Dalton’s law is based on experimental results. It is more accurate for gases at low pressures. Dalton’s law can be further extended to state the relationship of the internal energy, enthalpy, and entropy of the gases in a mixture as the Gibbs-Dalton law: ...
Post a Comment
Read more